How to Rip Plywood with Table Saw

Ripping plywood is more arduous due to the layering of the stuff. So, if you want to get high-quality results, you need to learn how to rip plywood with table saw. Trimming plywood sheets and boards with a saw table can be a difficult task. 

However, there are many ways to make rip plywood sheets simpler, more perfect, and with minimal scratching. To achieve this, all you need is to select the right table saw, which will keep away from issues and gets sheets without chips.  

6 Step Tips For Ripping Plywood with a Table Saw

Ripping plywood is more arduous due to the layering of the stuff. So, if you want to get high-quality results, you need to learn how to rip plywood with table saw. Trimming plywood sheets and boards with a saw table can be a difficult task.

However, there are many ways to make rip plywood sheets simpler, more perfect, and with minimal scratching. To achieve this, all you need is to select the right table saw, which will keep away from issues and gets sheets without chips.

How to Rip Plywood with Table Saw Step by Step

Step 1: Select the Suitable Blade

If you want to achieve the most straight and perfect plywood rip when cutting with a table saw, you must buy a unique blade with various numbers of teeth. We recommend you purchase an 80 TPI saw blade for plywood, which has 80 teeth per inch.

From our findings, most of the native table saw blades are only perfect for rough rips, not providing you neat and clean-cut edges. However, if you don’t want to purchase a saw table, you can locate a gap-free saw insert below the plywood sheet to rip. To achieve this, simply put a sheet of plywood on the table with the saw in functioning, ensuring that the plywood sheet does not slip out of your grip.

After the table saw has entirely ripped through the plywood, fasten the rip plywood sheet on the table with a vise.

Step 2: Clean the Table Saw Blade

Clean the Table Saw Blade

You must need to keep the table neat, clean, and polished. If you keep your table protected from rust and debris, it will not cause friction that will hinder the ripe plywood sheet.

As per our view, plywood sheets are made from various layers of wood fixed together, commonly with each layer at right angles to the following. There is no particular grain supervision. In this situation, a rip cut will be considered cut to length, and a cross-cut would be rip.

Step 3: Elevate the Table Saw Blade to Rip Perfectly

Elevating the table saw blade alternates the direction the blade’s teeth will rip the plywood sheet. Therefore, you will advance the edge slightly so that the teeth only softly and gently pass the plywood sheet. Besides, the blade’s teeth enter the sheet surface at a specific angle.

From our findings, if you raise the blade slightly higher, you can achieve a perpendicular rip. This means you will get a smoother plywood surface.

Moreover, avoid the table saw blade to elevate more than 1 inch above the plywood surface to rip. Make sure to use extreme caution when cutting a raised table saw blade.

Don’t forget to place the blade at the exact height for ripping. That means the table saw blade size must fit one tooth higher than the depth of plywood being rip.

Step 4: Place the Plywood in Opposition to the Table Saw Fence

Place the Plywood in Opposition to the Table Saw Fence

When you cut a big sheet of plywood on a table saw, always use an exit table to hold up the table when it comes off the saw blade.

Moreover, keep the most proper angle of the plywood against the fence. Then, you have to push the corner of the board into the wall to put it against the wall all around the rip.

Remember that never use a fence when doing a cross rip. If you do use it, then plywood will bond between the wall and saw table. We highly suggest, use a cross rip miter gauge.

Step 5: Support for Entire Plywood

Many large pieces of plywood can be heavy. During ripping them on a table saw blade, ensure they can be put flat before you begin the cut. You can stabilize the sheet with a desk or ask a friend to assist you to grip it firmly.

Providing support to the entire sheet permits you to keep a constant feed rate.

Step 6: Use a Tape on the Cut Mark

We suggest using low-tack tape on each of your plywood. Usage of tapes will assist keep the plywood fibbers in place and secure the edges from chipping. After finishing the ripping task, peel off the tape gently to avoid shattering.

Moreover, before you begin ripping the sheets of plywood with a table saw blade, a tape-tape strengthened with fiberglass or aluminum is gummed to the plywood. The essentials for its widths on both sides of the ripping line are a margin of 1.5.-2.0 cm.

Step 7: Rip the Plywood with Best Face Up

All you need is to lay the plywood out on the saw blade with the best side facing up. Afterward, the saw’s teeth will enter the blade from the top and way out from the bottom.

Step 8: Begin Cutting Plywood with a Table Saw Blade

At this step, you need to grip the saw blade stable and retain it pressed energetically against the guide, the straight edge of the saw. Always use both hands to guide the plywood via the saw blade.

Use the hand nearest to the saw blade to move the plywood next through the blade. Besides, use the hand far from the table saw blade to move the plywood toward the rip line.

Once you have become closer to the end of the rip, alter the position of your hands. Then cautiously move the remaining part of the foil through the blade. Always work carefully, and keep your hands away from the blade.

Related Question:

What Is The Best Way To Rip Plywood?

You can rip plywood sheets by using a table saw blade. You can cut them from one end of the sheet to the other, having the same edge tight along the plywood sheet edge. Besides, it is crucial to keep it nice and tight but also square so that the table saw blade rips square.

How Do You Cut A 4×8 Sheet Of Plywood On A Table Saw?

For cutting a 4×8 sheet of plywood on a table saw, you need to take two 2×4×8 and one 1×4×8 clamp and circular saw. In the first step, paint the 2×4×8 and lay them on the ground by leaving enough distance for the saw to fit between the boards. After this, adjust the depth of your blade to avoid cutting the floor. Now put the circular saw on the plywood with two blades.

Next, get a pencil and make a mark on the edge of the sauce. Once you have marked the measures, you can cut the piece of plywood.

Can You Rip A Board With A Table Saw?

Yes, you can cut a board with a table saw blade. But cutting long-boards can be tricky because the boards fall off the backside of the table, enticing you to get over the spinning blade to hold it.

What Sort Of Saw Do You Need To Rip Plywood?

You can use a circular saw or skill saw to cut plywood because this is the most common tool for this task. However, using this saw, it is hard to make lengthy and straight cuts without the assistance of a guide to keep the saw straight. You can solve this issue by simply clamping a board along the length of the plywood to use as a guide for your table saw.

Leave a Reply

Your email address will not be published.

Back to top button